PS5 HDMI Tool Buy
Free, nothing to installConvert the NOR with PS5 HDMI Tool

Reads, backs up and converts the PS5 Slim NOR with a CH341A reader.

Download for Windows
For PS5 Slim technicians

PS5 Interposer: swap the R$1,700 HDMI chip for an R$80 one.

The Interposer Tech MeoW puts the Nuvoton/Panasonic MN864739 on a board that requires the Realtek RTD2175P. Transparent flex, 1.8 V regulator already soldered and no wires on the board. You convert the NOR for free with our program.

  • Transparent flex
  • 1.8 V regulator soldered
  • No wires on the board
  • Free program
Interposer Tech MeoW for PS5 Slim: amber flexible board with the footprint for the MN864739 chip and the U1 regulator soldered

3D model made from the real drawing of the part. Drag to rotate and see both sides.

The repair math

Why repairing the PS5 HDMI chip used to be unviable

Some PS5 Slim boards leave the factory with the Realtek RTD2175P HDMI chip. When it fails, the console has no video and the replacement part weighs heavily on the repair quote. Prices below are in Brazilian reais (R$).

Part only, labor not included

Realtek RTD2175P R$1,700
Nuvoton/Panasonic MN864739, on average R$80

With labor, the repair with the Realtek gets close to R$3,000 for the customer, and many people give up. The interposer is what makes it possible to use the cheaper chip on this board. Reference prices: they change with the market.

Realtek RTD2175P chip sold still attached to a piece cut from another PS5 board

And the Realtek often arrives like this: cut out of another board.

How it works

From the dead chip to video again, layer by layer

Scroll the page and follow the HDMI chip swap on the board. The 3D model follows photos of the board and the real drawing of the interposer.

Loading the 3D model
1

The Realtek RTD2175P comes off the board

First of all, back up the NOR. Then remove the original HDMI chip and clean the pads. This is where the repair used to stall: the new part costs R$1,700.

Realtek RTD2175P on the PS5 Slim board, between the APU and the HDMI connector
2

The interposer takes its place

The transparent flex lets you see the board pads underneath: you align by looking, not guessing. The bottom side has the RTD2175P pinout, and the small holes let you solder by capillarity with the iron.

Real photo of the flex interposer on the PS5 board, with the board visible through it
3

The MN864739 goes on top

The Nuvoton or Panasonic chip, about R$80, is soldered on the top side. The arrow and the triangle on the silkscreen show the orientation and pin 1.

Real photo of the Nuvoton MN864739 HDMI chip soldered on the interposer on the PS5 board
4

The regulator handles the voltage

The Realtek PMIC, the small square next to the chip, provides 3.3 V and 0.9 V. The Nuvoton uses 0.9 V and 1.8 V. The interposer takes the 3.3 V from a Realtek pin and routes it to pin 1 of the U1 regulator, already soldered on the part. Pin 2 is GND, pin 3 (EN) gets the 0.9 V, and the 1.8 V output powers the new chip. No wire pulled from the CXD PMIC and no extra load on that circuit.

Interposer with the U1 1.8 V regulator soldered in the corner
5

PS5 HDMI Tool converts the NOR

The board only talks to the chip the NOR tells it to. The free program changes the NOR through the CH341A reader so the PS5 recognizes the new chip. Write it, power on and the video is back.

PS5 HDMI Tool screen with the option to write the NOR configured for Nuvoton
The part

What comes with the Interposer Tech MeoW

A flexible adapter board made to simplify bench repair: the technician solders the part to the board, solders the chip on top and that's it.

Transparent flex

You can see the other side while fitting it. Aligning the interposer pads with the board pads becomes much easier.

1.8 V regulator already soldered

U1 is a TI TLV71318 in SOT-23-5. It uses the 3.3 V already present at the Realtek pad and delivers the 1.8 V the MN864739 needs.

No wires on the board

The 1.8 V does not come from another point of the board. An overload in the video section stays contained in the part itself.

Power sequencing

The regulator EN pin is on the 0.9 V trace: the 1.8 V only rises once the 0.9 V is already there.

Passives mounted

Capacitors C1 to C7 come already on the part. Just solder and go.

Two sides, two chips

Bottom: the Realtek RTD2175P pinout. Top: the Nuvoton/Panasonic MN864739 pinout. No rerouting trace by trace.

Pin 1 marked

A triangle on both sides and an arrow for the new chip, to reduce the risk of mounting it reversed.

Transparent flex interposer on the PS5 Slim board, with the board copper and via showing through it
Real photo: the board shows through the flex.
Nuvoton MN864739 HDMI chip soldered on the interposer, already installed on the PS5 Slim board
Real photo: MN864739 soldered, already on the board.
Several PS5 interposers showing the front with the MN864739 pinout and the back with the RTD2175P pinout
Real photo: the part, front and back.
Comparison

Interposer with regulator, wired solution or a new Realtek?

The three ways to bring video back to a board that requires the RTD2175P.

What changesInterposer Tech MeoWWired interposerNew Realtek
Chip usedMN864739MN864739RTD2175P
Chip costAbout R$80About R$80About R$1,700
Wires on the boardNoYesNo
Where the 1.8 V comes fromU1 regulator, on the part itselfAnother point of the board, such as the CXD PMICNot used: the Realtek needs 3.3 V
Overload in the video sectionStays contained in the partCan reach the point the wire comes fromAs on the original board
Change the NORYes, free with PS5 HDMI ToolYesNot needed
The program

PS5 HDMI Tool: the NOR converted for free

The interposer solves the physical side. The NOR side is handled by our program, free and open source, made for the bench.

PS5 HDMI Tool screen: detect the CH341A reader, read the NOR, apply the Nuvoton patch and write the NOR
  • Reads and checks. Reads the NOR twice, compares byte by byte and only saves the backup if both match.
  • Converts both ways. Realtek ⇄ Nuvoton/Panasonic, with a preview before writing.
  • Writes with confirmation. Checks, erases, writes and verifies, with the progress on screen.
  • Analyzes .bin files. Shows the HDMI chip, the MAC and the board data, even with no board connected.
  • Also includes a UART reader, a controller test and an interface in Portuguese, English and Spanish.
  • A single file. Just open it on Windows. If the CH341A driver is missing, the program warns you and installs it.

Before writing a customer's board: check the log to see whether the conversion checksum came out as resolved. If the program warns that it did not, use it only on a bench board.

Installation

How to install the interposer on the PS5 Slim

A summary of the process. The full step-by-step guide, with photos and the location of the HDMI chip, is in the guide.

  1. NOR backup

    With the CH341A, read the NOR before touching the iron.

  2. Generate the conversion

    In the program, choose nuvoton and preview. Do not write yet.

  3. Remove the RTD2175P

    With flux and hot air, remove the chip and clean the pads.

  4. Solder the interposer

    183 °C paste, align pin 1 looking through the flex and reflow.

  5. Solder the MN864739

    On the top side, following the silkscreen arrow.

  6. Inspect

    Magnifier or microscope and multimeter, before powering on.

  7. Write and test

    Write the converted file, power on and test the video.

  8. Want the step-by-step guide?

    Open the full guideTest point map (PDF)
CH341A programmerCH341A programmer
Sugon 2020D hot air stationHot air station
Aifen A9 Pro soldering ironPrecision iron
Amtech NC-559 solder fluxSolder flux
183 degree solder paste183 °C solder paste

For technicians. Requires experience in SMD/QFN microsoldering and SPI NOR flashing. Done without preparation, it can destroy the motherboard, and the modification voids the console's factory warranty.

Buy

The part in the stores, the program for free

Interposer Tech MeoW
See the price in the stores

Sold on Mercado Livre and Shopee (Brazil).

  • Transparent flex, with both pinouts
  • 1.8 V regulator and capacitors mounted
  • For the MN864739, Nuvoton or Panasonic
  • Check in the store whether the chip is included
PS5 HDMI Tool
Free

No sign-up and no installation.

  • NOR reading, backup, conversion and writing
  • Works with the CH341A reader, on Windows
  • Tells you when a new version is out
Download the program
FAQ

Frequently asked questions about the PS5 HDMI chip

What is a PS5 interposer?

It is a thin adapter board that sits between the motherboard and the HDMI chip. The Interposer Tech MeoW is soldered onto the Realtek RTD2175P pads with its bottom side and takes the Nuvoton/Panasonic MN864739 on its top side.

How do I know if my PS5 uses the Realtek HDMI chip?

Check the marking on the chip between the APU and the HDMI connector: it must read RTD2175P. Do not rely on the position alone, especially on a board that has already been reworked. PS5 HDMI Tool also shows the HDMI chip configured in the NOR.

Which PS5 does the interposer work on?

The part and the program were made for PS5 Slim boards that use the Realtek RTD2175P HDMI chip.

Do I need to change the NOR after swapping the chip?

Yes. A board that leaves the factory with the Realtek only talks to the Realtek. PS5 HDMI Tool changes the NOR through the CH341A reader so the console recognizes the Nuvoton or Panasonic.

Do Nuvoton and Panasonic chips both work?

Yes. Both are the same MN864739, sold under the two brands on the replacement parts market.

How much does the PS5 HDMI chip cost?

As a reference, in Brazil the Realtek RTD2175P costs about R$1,700 for the part alone, and the MN864739 about R$80 on average. Prices change with the market. The interposer price is listed on our Mercado Livre and Shopee stores (Brazil).

Do I need to solder wires on the board?

No. The U1 regulator, already soldered on the part, takes the 3.3 V from the Realtek pad and delivers the 1.8 V the MN864739 needs.

What equipment do I need?

CH341A reader, hot air station, precision soldering iron, flux, low-temperature solder paste, multimeter and a microscope or magnifier.

Can I do it without microsoldering experience?

We do not recommend it. This job is for technicians experienced in microsoldering and NOR flashing. Done without preparation, it can destroy the motherboard.

The PS5 has no video after the swap. What should I check?

If the console powers on normally, suspect the soldering first: a cold joint, a bridge or a shifted chip. If it hangs on the blue check screen, make sure the program reported the conversion checksum as resolved.

Got a PS5 with no video sitting on your bench?

Buy the interposer, download the free program and close the repair. Do you run a repair shop, a store or a channel? Talk to us about partnerships.

Another project of ours

Meet PS-5 Controle Test

Test and calibrate the PS5 controller: buttons, sticks, drift, triggers and vibration. Free in the computer browser. On the phone, the Android app has 2 free days.

Learn about the project
Another project of ours

PS5 controller on the Nintendo Switch

Control PS-5 is a free app for hacked Nintendo Switch consoles: it connects the DualSense over Bluetooth, with no adapter, with adaptive triggers, light bar and per-game profiles.

See how to connect
Mercado Livre Shopee